As a Japanese local brand, Sony is deeply loved by people all over the world. Its netbooks are not only thin and light, but also very beautiful in appearance. Disassembly sounds like a very professional term to everyone. Most people are worried about making mistakes in disassembling and causing permanent damage to their beloved laptops. But the editor tells you that through the correct disassembly method, the heat sink inside the computer can be cleaned very well. Because during normal use, dust will inevitably enter the fan and heat sink. After being covered by dust, it is difficult for the notebook itself to dissipate heat, thereby reducing the computer's operating speed. Below, the editor will teach you the correct way to disassemble a Sony netbook, hoping to help you.
Step 1: Preparation before disassembling the Sony netbook: a Phillips screwdriver, a disassembly tab, a hair dryer, and some paper towels. Note: Before disassembling the machine, it is best to discharge the static electricity from your body. Breaking down the motherboard is no joke! You can wash your hands with tap water.
Step 2: There are no screws to fix the C case under the Sony netbook optical drive, so it is relatively easy to remove the keyboard; there are 4 buckles on the keyboard, which can be easily pried open with a flat-blade screwdriver; remove the ones on both sides of the memory After snapping, the memory will pop open at a 45-degree angle, and then it can be removed. Here you can note that the gold finger of the memory is visible. It is normal for a small part to be exposed when you install it, unlike desktop computers. You can't see the gold contacts that way.
Step 3: The next step is to disassemble the optical drive of the Sony netbook. Remove the screws around the optical drive to take out the optical drive. This is basically the case with other machines; then remove the D side ( Refers to the back of the notebook) Remove all the screws, including the screws hidden under the rubber pad (a total of6);
Step 4: The four screws in the lower right corner are used to fix the hard drive, so these four screws are different from other screws. Pay attention to the difference when removing them; remove the screws that fix the keyboard. After taking it off, you can remove the keyboard later.
Step 5: After removing all the screws, we turn the machine over and start to disassemble the keyboard of the Sony netbook; the side where the keyboard is located is called the C side. If you look carefully, you will find that there are four cards on the top of the keyboard. Buckle, use a small tool to push toward the screen, and push the little tongue inside. At the same time, you can use a pick to gently lift up the keyboard. This process is indeed a bit troublesome, so please be patient and take your time. Don't rush to pull out the keyboard after loosening all four bayonets.
Step 6: There is a cable attached to the bottom of the keyboard, just pull it out; you should carefully pull up the black cable buckle to the upper right to remove the keyboard cable. There are also three cables that need to be disassembled first by removing the black buckles.
Step 7: You can press the big hole with one hand. At this time, there will be a gap at the connection of the C surface. Just insert the disassembly tab into it and scratch it once. Open the C side; pull it to the left to remove the hard drive. Then directly remove the Sony Bluetooth module; there are two wire buckles: one is the speaker and the other is the card reader; fasten the two ends with your fingernails and pull them off easily.
Step 8: Pay attention to the display cable. Don’t pull on the blue strip here. If you are afraid of breaking it, you can directly pinch the two black ends and pull it out, and it will be removed; clean the dust and remove the motherboard. There is no need to disassemble the display screen. Last time, the machine oil dismantled the display screen for cleaning purposes. Just unplug this cable and there is no need to disassemble the display screen.
Step 9: Next, remove the USB interface cable of the Sony netbook, just hold it with both hands and push it; then remove the screws on the motherboard, insert your fingers between the two boards, and pull up Let it separate and you can pick up the motherboard.
Finally, take out the radiator and fan, and the entire disassembly process is over. Then you can clean the removed radiator and fan, and then add an appropriate amount of lubricating oil to the fan to ensure that it can rotate normally. After the entire process is completed, you can put the notebook back in sequence in the order of steps 987654321. Install the screws, restart the computer, and after running for a while, you will find that the temperature of the netbook is not so high and the running speed has become faster. Follow the editor's steps, I believe you will learn how to use Sony to surf the InternetThe correct way to disassemble the machine.